Parts List
Installation Guide
Beer Dispenser
866-319-5473
For assistance, please call:
1
1
Install Caster Wheels
Make sure unit is empty (including white metal keg floor(11)). Carefully
tip the beer dispenser on its side. Connect the casters(13) to the cabinet
by screwing in each metal bracket into one of four caster holes (casters
in the front of the cabinet require the washers(12)). Then carefully set
the unit upright
Note: allow dispenser to stand in an upright position for 8 hours
before turning on the power.
2
Remove Plug
Open the door, and with your hand push the top cabinet plug
through the top of the cabinet. Use flat head screwdriver as a prying
tool if necessary.
3a
Install Tower
Now begin installing the tower(3). Unravel the beer line hose from the
bottom of the tower, and feed the hex nut and beer line through the hole
you uncovered in the top of the cabinet.
3b
Secure Tower
Once you have fed all the line into the cabinet, you can now place the
tower into the unit. Align the black plastic adapter on the bottom of the
tower to the hole in the top of the cabinet. The adapter should mate
securely with the hole. Then turn the adapter about 25° to lock it into
place. The faucet connection for the tower should now face the front of the
cabinet. If the tower is not facing the front of the cabinet, remove it and
reinstall it from another position.
4
Install Railing
Take the railing(4) and slide its
“feet” into the pilot holes in the
top of the cabinet
Thank you for purchasing the EdgeStar Beer Dispenser.
Are you ready to enjoy some draft beer now?
All you need is:
• Included components (pictured to the left)
• Wrench
• Flat head screwdriver
• Pair of pliers/clamp crimper
• Full keg of beer (1/2 barrel size or smaller [pictured to the left but not included])
Note: Any Coors Brand or Miller Rubber Sided kegs will not fit inside this unit.
• Also, fill the included CO
2
tank with CO
2
(Most beer keg providers can fill your CO
2
tank)
Notice: this manual is provided as a supplement to the owner’s manual. Please refer to the owner’s
manual for a full discourse on installation, usage and maintenance.
Note: Parts listed throughout this installation guide are numbered according to the diagram parts list.
1
2
3
4
6
7
10
8
5
9
11
12
13
1. Faucet Handle
2. Faucet
3. Beer Tower
4. Guard Rail
5. Drip Tray
6. Regulator
7.
CO
2
Tube
8.
CO
2
Cylinder (supplied empty)
9. Cylinder Holder
10. American Sankey Keg Coupler
11. Metal Keg Floor Support
12. Caster Washer (x2)
13. Casters (x4)
14. Neoprene Washer
15. Snap-On Clamps (x2)
16. Wire Shelves (not shown) (x2)
17. Half Barrel Keg (not included)
18. Faucet Wrench
17
14
15
Warning: CO
2
can be dangerous! CO
2
cylinders contain high-pressure gas, which can be hazardous if
handled improperly. Please handle with care.
Note: Included accessories may not be as pictured
Warning: This guide is provided for informational purposes only. If you have any questions about
the installation of this appliance, feel free to contact EdgeStar service at 866.319.5473 or consult
a qualified installer. Neither the manufacturer nor its distributors shall be liable for any incidental,
consequential, indirect, special, or punitive damages of any nature, including without limitation,
lost revenues or profits, or any other damage whether based in contract, tort, or otherwise.
18
(11 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals